Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment

M. Nuckols, S. Kolaczkowski, S. Awdry, T. Smith, D. Thomas

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

Traditional CO2 absorption methods for underwater life support equipment use alkali metal hydroxide chemical beds- mostly calcium hydroxide-that have been shown to have poor absorption efficiencies at cold temperatures, and must be replaced at considerable trouble and expense on a frequent basis. With chemical utilizations as low as 20% in water temperatures of 2°C, these hydroxides do not lend themselves to applications requiring extended durations in cold water due to the inability to carry sufficient quantities of expendables. A joint research effort between Duke University and the University of Bath has verified the feasibility in laboratory trials of an alternative carbon dioxide removal method that intimately mixes seawater with breathing circuit gases within a packed bed of Dixon rings. Based on the results of these laboratory trials, two multi-path scrubber prototypes were designed and fabricated for unmanned testing. In March 2013, the hyperbaric performance of these prototype scrubbers was characterized over a wide range of gas and water flow rates when operating the scrubbers in counter-current (water flowing in the opposite direction as gas flow) and co-current (water flowing in the same direction as gas flow) fashion. Significant findings from these tests included the following: Both scrubber prototypes were found to be capable of delivering exit CO2 levels below 0.5 vol% (surface equivalent) at respiratory rates up to 22.5 liters per minute and at depths ranging from 0 to 40 meters of seawater (MSW). Negligible collateral O2 absorption was observed at surface pressure (exit O2 levels were typically above 20.2 vol%), and exit O2 levels were typically above 18.4% during testing at 10 MSW. At surface pressure, both prototypes had significantly lower breathing resistances than design goals established by the U. S. Navy.

LanguageEnglish
Title of host publicationASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering
PublisherAmerican Society of Mechanical Engineers (ASME)
Volume8A
ISBN (Print)9780791845509
DOIs
StatusPublished - 2014
EventASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering, OMAE 2014 - San Francisco, UK United Kingdom
Duration: 8 Jun 201413 Jun 2014

Conference

ConferenceASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering, OMAE 2014
CountryUK United Kingdom
CitySan Francisco
Period8/06/1413/06/14

Fingerprint

Scrubbers
Carbon dioxide
Seawater
Testing
Water
Flow of gases
Hydrated lime
Packed beds
Alkali metals
Gases
Flow rate
Temperature
Networks (circuits)

Cite this

Nuckols, M., Kolaczkowski, S., Awdry, S., Smith, T., & Thomas, D. (2014). Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment. In ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering (Vol. 8A). [V08AT06A003] American Society of Mechanical Engineers (ASME). DOI: 10.1115/OMAE2014-23028

Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment. / Nuckols, M.; Kolaczkowski, S.; Awdry, S.; Smith, T.; Thomas, D.

ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering. Vol. 8A American Society of Mechanical Engineers (ASME), 2014. V08AT06A003.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Nuckols, M, Kolaczkowski, S, Awdry, S, Smith, T & Thomas, D 2014, Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment. in ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering. vol. 8A, V08AT06A003, American Society of Mechanical Engineers (ASME), ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering, OMAE 2014, San Francisco, UK United Kingdom, 8/06/14. DOI: 10.1115/OMAE2014-23028
Nuckols M, Kolaczkowski S, Awdry S, Smith T, Thomas D. Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment. In ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering. Vol. 8A. American Society of Mechanical Engineers (ASME). 2014. V08AT06A003. Available from, DOI: 10.1115/OMAE2014-23028
Nuckols, M. ; Kolaczkowski, S. ; Awdry, S. ; Smith, T. ; Thomas, D./ Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment. ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering. Vol. 8A American Society of Mechanical Engineers (ASME), 2014.
@inproceedings{8a81e29bb5ea41a5a2724bef3dbbcbdc,
title = "Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment",
abstract = "Traditional CO2 absorption methods for underwater life support equipment use alkali metal hydroxide chemical beds- mostly calcium hydroxide-that have been shown to have poor absorption efficiencies at cold temperatures, and must be replaced at considerable trouble and expense on a frequent basis. With chemical utilizations as low as 20{\%} in water temperatures of 2°C, these hydroxides do not lend themselves to applications requiring extended durations in cold water due to the inability to carry sufficient quantities of expendables. A joint research effort between Duke University and the University of Bath has verified the feasibility in laboratory trials of an alternative carbon dioxide removal method that intimately mixes seawater with breathing circuit gases within a packed bed of Dixon rings. Based on the results of these laboratory trials, two multi-path scrubber prototypes were designed and fabricated for unmanned testing. In March 2013, the hyperbaric performance of these prototype scrubbers was characterized over a wide range of gas and water flow rates when operating the scrubbers in counter-current (water flowing in the opposite direction as gas flow) and co-current (water flowing in the same direction as gas flow) fashion. Significant findings from these tests included the following: Both scrubber prototypes were found to be capable of delivering exit CO2 levels below 0.5 vol{\%} (surface equivalent) at respiratory rates up to 22.5 liters per minute and at depths ranging from 0 to 40 meters of seawater (MSW). Negligible collateral O2 absorption was observed at surface pressure (exit O2 levels were typically above 20.2 vol{\%}), and exit O2 levels were typically above 18.4{\%} during testing at 10 MSW. At surface pressure, both prototypes had significantly lower breathing resistances than design goals established by the U. S. Navy.",
author = "M. Nuckols and S. Kolaczkowski and S. Awdry and T. Smith and D. Thomas",
year = "2014",
doi = "10.1115/OMAE2014-23028",
language = "English",
isbn = "9780791845509",
volume = "8A",
booktitle = "ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering",
publisher = "American Society of Mechanical Engineers (ASME)",
address = "USA United States",

}

TY - GEN

T1 - Hyperbaric testing of an alternative approach to remove carbon dioxide from underwater life support equipment

AU - Nuckols,M.

AU - Kolaczkowski,S.

AU - Awdry,S.

AU - Smith,T.

AU - Thomas,D.

PY - 2014

Y1 - 2014

N2 - Traditional CO2 absorption methods for underwater life support equipment use alkali metal hydroxide chemical beds- mostly calcium hydroxide-that have been shown to have poor absorption efficiencies at cold temperatures, and must be replaced at considerable trouble and expense on a frequent basis. With chemical utilizations as low as 20% in water temperatures of 2°C, these hydroxides do not lend themselves to applications requiring extended durations in cold water due to the inability to carry sufficient quantities of expendables. A joint research effort between Duke University and the University of Bath has verified the feasibility in laboratory trials of an alternative carbon dioxide removal method that intimately mixes seawater with breathing circuit gases within a packed bed of Dixon rings. Based on the results of these laboratory trials, two multi-path scrubber prototypes were designed and fabricated for unmanned testing. In March 2013, the hyperbaric performance of these prototype scrubbers was characterized over a wide range of gas and water flow rates when operating the scrubbers in counter-current (water flowing in the opposite direction as gas flow) and co-current (water flowing in the same direction as gas flow) fashion. Significant findings from these tests included the following: Both scrubber prototypes were found to be capable of delivering exit CO2 levels below 0.5 vol% (surface equivalent) at respiratory rates up to 22.5 liters per minute and at depths ranging from 0 to 40 meters of seawater (MSW). Negligible collateral O2 absorption was observed at surface pressure (exit O2 levels were typically above 20.2 vol%), and exit O2 levels were typically above 18.4% during testing at 10 MSW. At surface pressure, both prototypes had significantly lower breathing resistances than design goals established by the U. S. Navy.

AB - Traditional CO2 absorption methods for underwater life support equipment use alkali metal hydroxide chemical beds- mostly calcium hydroxide-that have been shown to have poor absorption efficiencies at cold temperatures, and must be replaced at considerable trouble and expense on a frequent basis. With chemical utilizations as low as 20% in water temperatures of 2°C, these hydroxides do not lend themselves to applications requiring extended durations in cold water due to the inability to carry sufficient quantities of expendables. A joint research effort between Duke University and the University of Bath has verified the feasibility in laboratory trials of an alternative carbon dioxide removal method that intimately mixes seawater with breathing circuit gases within a packed bed of Dixon rings. Based on the results of these laboratory trials, two multi-path scrubber prototypes were designed and fabricated for unmanned testing. In March 2013, the hyperbaric performance of these prototype scrubbers was characterized over a wide range of gas and water flow rates when operating the scrubbers in counter-current (water flowing in the opposite direction as gas flow) and co-current (water flowing in the same direction as gas flow) fashion. Significant findings from these tests included the following: Both scrubber prototypes were found to be capable of delivering exit CO2 levels below 0.5 vol% (surface equivalent) at respiratory rates up to 22.5 liters per minute and at depths ranging from 0 to 40 meters of seawater (MSW). Negligible collateral O2 absorption was observed at surface pressure (exit O2 levels were typically above 20.2 vol%), and exit O2 levels were typically above 18.4% during testing at 10 MSW. At surface pressure, both prototypes had significantly lower breathing resistances than design goals established by the U. S. Navy.

UR - http://www.scopus.com/inward/record.url?scp=84911164496&partnerID=8YFLogxK

UR - http://dx.doi.org/10.1115/OMAE2014-23028

U2 - 10.1115/OMAE2014-23028

DO - 10.1115/OMAE2014-23028

M3 - Conference contribution

SN - 9780791845509

VL - 8A

BT - ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering

PB - American Society of Mechanical Engineers (ASME)

ER -