Skip to main navigation Skip to search Skip to main content

Green synthesis of vinasse based nano-biochar polymer composite membrane and evaluation of their performance

  • Necmettin Erbakan University
  • Division G - Qualitative Hydrology
  • Federal Institute of Hydrology (BfG)
  • Institute for Integrated Natural Sciences
  • University of Koblenz

Research output: Contribution to journal › Article › peer-review

Abstract

This study presents a novel approach to fabricate three-dimensional (3D) membranes by depositing a nano-biochar (NBC) polymeric composite onto 3D-printed flat and spiral supports, offering a sustainable alternative to conventional membranes. Biochar derived from vinasse, an industrial waste, was refined to the nanoscale via high-energy ball milling. NBC was incorporated as a filler into a polyethersulfone (PES) matrix using Cyrene as an eco-friendly solvent. At an optimized 0.25 wt% NBC loading (NBC25@PES), membrane porosity increased to 78% ± 4.9%, the surface charge became more negative (−27.4 mV at pH 7), and the contact angle dropped to 48° ± 2°. Compared to bare PES, pure water permeance (PWP) increased from 1.5 ± 0.2 to 3.3 ± 0.5 LMH/bar, maintaining a 96% ± 1.3% Rose Bengal rejection. A mass balance of 93.8% ± 2.1% confirmed minimal surface adsorption. The molecular weight cut-off (MWCO) ranged from 400 to 1000 Da, aligning with nanofiltration characteristics. Furthermore, the NBC25@PES composite layer was deposited onto 3D-printed flat and spiral supports via vacuum filtration. The spiral composite membranes exhibited a significantly enhanced PWP, increasing by approximately 40% from 3.54 ± 0.5 LMH/bar (flat) to 4.96 ± 0.6 LMH/bar. During PEG1000 filtration, flat and spiral configurations achieved rejections of 97% ± 2.15% and 98% ± 1.25%, with permeances of 2.80 ± 0.4 and 3.72 ± 0.2 LMH/bar, respectively. Notably, the spiral configuration mitigated fouling by enhancing initial permeance, a consequence of its higher surface area to footprint ratio relative to the flat. These results demonstrate the high potential of 3D-printed biochar composite membranes for advanced wastewater treatment.

Original languageEnglish
Article number140317
Number of pages13
JournalSeparation and Purification Technology
Volume420
Early online date25 Sept 2026
DOIs
Publication statusE-pub ahead of print - 25 Sept 2026

Data Availability Statement

Data will be made available on request.

Acknowledgements

Omer KAZAK gratefully acknowledges TÜBITAK (The Scientific and Technological Research Council of Türkiye) for awarding him an International Postdoctoral Research scholarship (1059B192202872). He also thanks Necmettin Erbakan University (Türkiye) for supporting his postdoctoral research stay at the University of Bath, UK. The authors appreciate the assistance of the Material and Chemical Characterization Facility (MC2) and the Faculty of Engineering & Design technical services at the University of Bath. Special thanks are extended to Prof. Dr.
Ali TOR for his valuable contributions.

Funding

Omer KAZAK gratefully acknowledges TÜBITAK (The Scientific and Technological Research Council of Türkiye) for awarding him an International Postdoctoral Research scholarship (1059B192202872).

FundersFunder number
The Scientific and Technological Research Council of Türkiye1059B192202872

    Keywords

    • 3D printed
    • Biochar
    • Composite membrane
    • Green solvents
    • Membrane

    ASJC Scopus subject areas

    • Analytical Chemistry
    • Filtration and Separation

    Fingerprint

    Dive into the research topics of 'Green synthesis of vinasse based nano-biochar polymer composite membrane and evaluation of their performance'. Together they form a unique fingerprint.

    Cite this